<pre id="xlbpv"><sub id="xlbpv"></sub></pre>

          <sub id="xlbpv"><th id="xlbpv"><thead id="xlbpv"></thead></th></sub>
          <nobr id="xlbpv"><meter id="xlbpv"></meter></nobr>

          <var id="xlbpv"><meter id="xlbpv"></meter></var>

            English | 添加收藏 | 設為首頁
            您所在的位置:網站首頁 > > 產品中心 > 汽車線束絕緣材料 > PE汽車線125℃/150℃輻照交聯柔軟阻燃汽車線料(含鹵,大平方線) FEJZ125S, FEJZ150S
            125℃/150℃輻照交聯柔軟阻燃汽車線料(含鹵,大平方線) FEJZ125S, FEJZ150S
            125/150℃ Soft Irradiation Cross-linkable Halogenous Flame-retardantLarge Square Meter Automotive Cable Compound...
            型號:0

            參考價:¥

            說明:如您對該產品感興趣,請在此輸入您的手機號將本產品的地址 發送至您手機上。
            Product Description and Application 產品描述和用途
            Soft irradiation cross-linkable flame-retardant automotive cable compound which are produced by mixing, plasticizing and pelletizing process, regards polyolefin resin as the basic raw materials, adds flame retardant, anti-oxidant, sensabilizer. The highest working temperature are respectively 125℃and 150℃. The cables with them can meet ISO 6722 and DIN 72551 Standards. They are suitable for the insulation layers of 16 square meters and above of automotive cables.
            輻照交聯柔軟阻燃汽車線料是以聚烯烴樹脂為主要原料,加入阻燃劑,抗氧劑,助交聯劑,經混煉、塑化、造粒而得,最高工作溫度分別為125℃和150℃。制成電線后可以滿足ISO6722,DIN 72551標準,適用于16以上平方汽車線擠出絕緣層。
             
            Processing Indicator 加工工藝
            General PVC or PE extruder is possible for the production of it. Recommend screw extruder with L/D≥25. It is better to put one 80 mesh filter on the position of screen while extruding. Temperatrue range changes according to different conditions of extruding equipment. Below temperature is just for boot debugging.
            本產品可采用普通PVC或PE擠出機進行生產,建議螺桿長徑比L/D≥25,擠出過程中可在網板放置一層80目濾網。溫度的選擇應根據所用擠塑機的具體情況選定。下列各溫度可作為開機調試的參考:
            Temperature Zone
            溫區 
            Z1 Z2 Z3 Z4 H1 H2 H3 H4
            Setting Temperature
            設定溫度
            140 150 155 160 160 165 165 170
             
            Conductor preheated to 110 ℃, and warm bath temperature about 40~60℃
            導體預熱至110℃,溫水槽溫度40~60℃左右。
             
            Irradiation Process輻照工藝
            Irradiation dose of irradiation cross-linkable polyolefin automotive cables compound should be given according to thermal strength requirements (note: different accelerators with the same irradiation dose will cause different thermal strength values). The thermal strength shoul be controlled between 20%-40%. Generally speaking, the more bigger conductor, the larger irradiation dose amount.
            輻照交聯型聚烯烴汽車線的輻照劑量應根據應以熱延伸達到要求為準(不同單位加速器按同一輻照劑量,其熱延伸值不一樣),本產品熱延伸需控制在20%~40%范圍內,導體越大,輻照劑量應適當的提高。
             
            Attentions 注意事項:
            1)The compound should be dried before using if the package is broken. Once package is open, recommend to run out within 12 hours.
            原料破包需烘干后才能使用,材料一經開封,建議12小時之內用完。
            2)Please ensure the screw, barrel , hopper are thoroughly cleaned before operation. Avoid bringing impurities while processing.
            加工前確保螺桿、機筒、加料斗徹底清理干凈,加工過程中嚴禁帶入雜質。
            3)If you need a faster extrusion. Please accelerate screw speed gradually to avoid inadequate plasticizing which may cause rough surface of the cables.
            如果要快速擠出時,請慢慢逐漸加快螺桿轉速,以免塑化不良,電纜表面毛糙。
             
            Physical and Electrical Properties物理和電氣性能
            Item
            試驗項目
            Unit
            單位
            FEJW125R FEJW150R
            Tensile Strength
            拉伸強度
            MPa ≥10 ≥10
            Elongation at Break
            斷裂伸長率
            % ≥200 ≥200
            Density
            密度
            g/cm3 ≤1.35 ≤1.35
            Dielectric Strength
            介電強度
            MV/m ≥20 ≥20
            Thermal Aging Condition
            熱老化條件
            / 150℃×240h 180℃×240h
            Tensile Strength Variation after Aging
            老化后拉伸強度變化率
            % ±20 ±20
            Elongation Variation after Aging
            老化后斷裂伸長率變化率
            % ±20 ±20
            Brittle Temperature with Impact
            沖擊脆化溫度
            -40 -40
            20℃Volume Resistivity
            20℃體積電阻率
            Ωm ≥1.0×1012 ≥1.0×1012
            Hot Set Test Condition
            熱延伸試驗條件
            200℃×0.2MPa×15min
            Hot Elongation
            負荷下伸長率
            % ≤100 ≤100
            Permanent Deformation after Cooling
            冷卻后永久形變
            % ≤5 ≤5
            Oxygen Index
            氧指數
            % ≥24 ≥24
            Hardness
            硬度
            Shore A 80±2 80±2

            日本免费无遮挡吸乳视频中文字幕,色欧美片视频在线观看,日本免费无遮挡吸乳视频中文字幕,性生大片免费观看性